New H160 Loader

Loaders
REQUEST A QUOTE
REQUEST A QUOTE
Key Features
  • Compatible with 3R Series Tractors
  • Quik-Park™ mounting system for efficient attachment and removal
  • Easy maintenance for increased uptime
  • 999 pounds (453 kg) lift capacity

More Info

Features

End-of-pin lubrication means easy maintenance
Close up of grease fittingClose up of grease fitting
Pivot point grease fitting locationsPivot point grease fitting locations

All pivot points on the loader have grease fittings that are accessible from the side of the loader to make greasing the loader much easier, ensuring that all grease points are more likely to be serviced. No more searching for grease points that are hard to find. Removing the grease gun from the grease fitting or zerk is not a problem either as sufficient radius has been left to allow the grease gun tip to be rotated to the side for removal from the fitting or zerk.

Quik-Park™ loader mounting system
Quik-Park loader mounting systemQuik-Park loader mounting system

The H-Series Loaders are designed for easy removal and mounting to and from the tractor without tools.

The parking stand, attached to the front frame of the tractor, is an integral part of the loader during loader operation.

The parking stand lowers into position by moving the joystick to the raised position once the latches are opened. This allows the loader to move to the parked position.

To view a video of how the Quik-Park™ system works click here.

NOTE: This video only shows the dismount and mount of the loader without disconnecting the hydraulics. To completely remove the loader, the operator must turn the tractor off, relieve the hydraulics, and then disconnect the hoses from the couplers.

Specifications

Compare >>>

Select up to 2 models to compare specifications

John DeereH160 Loader
Add Model
Add Model
Tractor
Model 3120/3320/3520/3720
Front tire 7.00-14 6PR R1
Rear tire 11.2-24 6PR R1
Front axle configuration
Wheelbase 1727 mm
68 in.
Pump capacity 8.6 gpm
Rated pressure 2500 psi
Loader
Leveling configuration
Bucket used
Bucket weight 93.8 kg
206.8 lb
Lift capacity at full height Measured at pivot (U)
617 kgf
1360 lbfMeasured at 500 mm ahead of pivot (V)
453 kgf
999 lbf
Lift capacity at 59 in. (1500 mm) Measured at pivot (W)
771 kgf
1700 lbfMeasured at 500 mm ahead of pivot (X)
595 kgf
1312 lbf
Boom breakout force Measured at pivot (Y)
1295 kgf
2855 lbfMeasured at 500 mm ahead of pivot (Z)
922 kgf
2032 lbf
Bucket rollback force capacity At maximum height (VV)
1205 kgf
2657 lbfAt 59-in. (1500-mm) lift height (XX)
1518 kgf
3347 lbfAt ground-level line (ZZ)
1188 kgf
2619 lbf
Dimensions Maximum lift height (A)
2284 mm
90 in.At full height - bucket level(B)
83.5 in.
2123 mmAt full height - bucket dumped (C)
1743 mm
68.6 in.
Overall length (I+F), ft (m) 3.122 m
10.24 ft
Overall height in carry position (J)
Digging depth (H) 76 mm
2.9 in.
Reach At maximum height (D)
773 mm
30.4 in.At ground level - bucket level (F)
1381 mm
54.4 in.
Bucket angle Dump angle, degrees (E)
43 degree (angle)Rollback angle, degrees (G)
25 degree (angle)
Cycle times Loader raise, seconds
2.76 secondsLoader lower, seconds
1.69 secondsBucket dump, seconds
2.91 secondsBucket rollback, seconds
1.72 seconds

Accessories and Attachments

Ballast Box

Ballast Box - BW15073
#

Ballast box can be used to carry additional ballast for greater tractor stability.

 

A 23-cm (9-in.) high extension can be added to ballast box for even greater capacity.

 

The hitch utilizes a standard Category 1 configuration for connection to the tractor Category 1 hitch.

 

A bushing kit is required for the ballast box to be used with the iMatch™ Quick-Hitch.

Ballast Box Extension - BW15074

Buckets

53 In. (1350mm) Loader Materials Bucket - Quik Change - BW14145
Materials bucketMaterials bucket

Materials buckets are available to match tractor-loader applications. The buckets may be used for loading dirt, gravel, feed, and light materials as well as scraping, digging, and other general-purpose tasks. The top surface of the bucket is parallel to the cutting edge, which aids the operator as a leveling guide.

 

There is a quik-change connection for easy on/off.

 

When the 220R Loader is ordered factory installed on model year 2017 2R Tractors, the 1450-mm (57-in.) materials bucket is base equipment.

 

For non-model year 2017 2R Tractors, the bucket and other specific configuration items will need to be ordered through Parts (such as mounting frames, and hood guard).

61 In. (1550 mm) Loader Heavy Duty Bucket with Holes for Cutting Edge - BW14764
Heavy-duty bucketsHeavy-duty buckets

Heavy-duty buckets are available for tasks requiring more robust bucket designs. Recommended for heavier use applications, such as commercial operations.

 

Top surface of the bucket is parallel to the cutting edge, which aids operator as a leveling guide.

 

Additional strength is built into the bucket design with additional wear bars, boxed top bucket section, and bucket end plate supports.

 

Cutting edge has pre-drilled holes for addition of a replaceable cutting edge.

61 In. (1550mm) Loader Materials Bucket - Quik Change - BW14146
1550-mm (61-in.) materials bucket1550-mm (61-in.) materials bucket

Materials buckets are available to match tractor-loader applications. The buckets may be used for loading dirt, gravel, feed, and light materials as well as scraping, digging, and other general-purpose tasks.

 

IMPORTANT: Materials buckets are not recommended for heavy-duty tasks. For heavier use applications, use heavy-duty bucket.

 

The top surface of the bucket is parallel to the cutting edge, which aids the operator as a leveling guide.

 

There is a quik-change connection for easy on and off.

 

The round-back design helps material flow when filling or dumping the bucket.

73 In. (1850 mm) Loader Heavy Duty Bucket with Holes for Cutting Edge - BW14765
Heavy-duty bucketsHeavy-duty buckets

Heavy-duty buckets are available for tasks requiring more robust bucket designs. Recommended for heavier use applications, such as commercial operations.

 

Top surface of the bucket is parallel to the cutting edge, which aids operator as a leveling guide.

 

Additional strength is built into the bucket design with additional wear bars, boxed top bucket section, and bucket end plate supports.

 

Cutting edge has pre-drilled holes for addition of a replaceable cutting edge.

73 In. (1850mm) Loader Materials Bucket - BW14147
Materials bucketsMaterials buckets

Materials buckets are available to match tractor and loader applications. May be used for loading dirt, gravel, feed and light materials, as well as scrapping, digging and other general purpose tasks.

 

IMPORTANT: Materials buckets are not recommended for heavy-duty tasks. For heavier-use applications, use the heavy-duty bucket.

 

Top surface of the bucket is parallel to cutting edge, which aids operator as a leveling guide.

Quik-Change connection for easy on and off.

 

Round-back design helps material flow when filling or dumping the bucket.

Cutting Edges

61 In. (1550 mm) Replaceable Bucket Cutting Edge with Hardware - BW14762

Recommended for heavier use applications, such as commercial operations and rental customers.

 

Additional strength is added to the cutting edge and the replaceable cutting edge is reversible for longer wear life.

 

Not compatible with tooth bars.

 

NOTE:  Heavy-duty buckets come standard with the holes to install the replaceable cutting edge.  Standard materials buckets require installation of attaching holes.

73 In. (1850 mm) Replaceable Bucket Cutting Edge with Hardware - BW14763
Bucket cutting edgeBucket cutting edge
Closeup of cutting edgeCloseup of cutting edge
Hardware for cutting edgeHardware for cutting edge

Recommended for heavier-use applications, such as commercial operations and rental customers. Additional strength is added to the cutting edge. Replaceable and reversible cutting edge for longer wear life.

 

HITCH ADAPTERS

iMatch Bushing Kit - BW15056
iMatch quick-coupler bushing kitiMatch quick-coupler bushing kit

Bushing kit for use with Category 1 implements (ballast box) to make them function correctly with the iMatch Quick-Hitch.

Hood Guards

Deluxe Hood Guard Attachment - BW15222
Deluxe hood guard attachmentDeluxe hood guard attachment

Hood guard attachment to make BW15219 or BW15221 into a deluxe hood guard.

Deluxe Hood Guard Attachment - BW16585
Deluxe hood guard attachmentDeluxe hood guard attachment

Hood guard attachment to make BW15219 or BW15221 into a deluxe hood guard.

Hood Guard - BW14378
Hood guard for 4000 and 4010 Series TractorsHood guard for 4000 and 4010 Series Tractors

A hood guard can be ordered for a tractor without ordering a loader.

 

The hood guard protects the front of the tractor while operating the loader.

 

The bolt-on design stays with tractor when loader is removed.

Hood Guard - BW15219
Hood guard for 3000 TWENTY Series TractorsHood guard for 3000 TWENTY Series Tractors

A hood guard can be ordered for a tractor without ordering a loader.

 

The hood guard protects the front of the tractor while operating the loader.

 

The bolt-on design stays with tractor when loader is removed.

 

The hood guard for the 3000 TWENTY Series Tractors pivots forward to allow the tractor hood to be raised.

Hood Guard - BW16617

A hood guard can be ordered for a tractor without ordering a loader.

The hood guard protects the front of the tractor while operating the loader.

The bolt-on design stays with tractor when loader is removed.

Hood Guard (3203) - BW15534

A hood guard can be ordered for a tractor without ordering a loader.

The hood guard protects the front of the tractor while operating the loader.

The bolt-on design stays with tractor when loader is removed. 

Hydraulics

Hoses and Parts - BW15599

This bundle consists of the hoses and parts to connect from the loader boom hydraulic lines of the 300X and H160 Loader to the mid-mount area hydraulic couplers on the right-hand side of the compatible tractor.

Miscellaneous

Bucket Level Indicator - BW15223
Bucket level indicatorBucket level indicator

The bucket level indicator assists the operator to determine the attachment position at ground level.

 

It is adjustable to indicate level position for different attachments such as pallet forks and buckets.

 

The indicator is adjusted to have the bend of the rod rest in the bracket when the attachment is level at ground.

Mounting Frames

Mounting Frame (3320-3720, 4320-4720 Cab Tractors) - BW15456
Cab mounting frameCab mounting frame

Mounting frames are designed at the same time as the tractor in order to provide durable and yet very simple attaching points for the loader. The mounting frames bolt to the tractor chassis and do not restrict tractor use when the loader is not installed.

Mounting Frame (4200-4400, 4210-4400, 3120-3720, 3203 Open Station Tractors) - BW15204
Open-station mounting frameOpen-station mounting frame

Mounting frames are designed at the same time as the tractor in order to provide durable and yet very simple attaching points for the loader. The mounting frames bolt to the tractor chassis and do not restrict tractor use when the loader is not installed.

Mounting Frame with Hoses and Parts (3320-3720 Cab Tractors) - BWA1248

Mounting frames are designed at the same time as the tractor in order to provide durable and yet very simple attaching points for the loader. The mounting frames bolt to the tractor chassis and do not restrict tractor use when the loader is not installed.

Tooth Bars

61 In. (1550 mm) Tooth Bar for Bucket - BW15227
Tooth barTooth bar

The tooth bar helps penetrate hard-packed material.  It attaches to the bucket by sliding over the cutting edge and is retained by two bolts, one in each end plate of the bucket.

  • Holes must be drilled in bucket end plates to retain the tooth bar
  • Protrudes beyond bucket edge approximately 150 mm or 6 in.
  • Recommended for use with heavy-duty buckets only
  • Not compatible with buckets with replaceable cutting edge installed